Publication:
Modeling and Control of MEMS-based Multi-layered Prestressed Piezoelectric Cantilever Beam

dc.contributor.advisor Pota, Hemanshu
dc.contributor.advisor Woldeghiorgis, Aron
dc.contributor.author Nawaz, Muhammad Haq
dc.date.accessioned 2023-11-13T22:13:12Z
dc.date.available 2023-11-13T22:13:12Z
dc.date.issued 2023
dc.date.submitted 2023-11-13T05:22:01Z
dc.description.abstract Piezoelectric materials are the preferred smart materials for sensing and actuation in the form of micro and nano-engineering structures like beams and plates. Cantilever beams play a significant role as key components in atomic force microscopy and bio and chemical sensors. Adding an active layer such as lead zirconate titanate (PZT) thin-film to form smart cantilever beams with sensing and actuation capabilities is highly desirable to facilitate miniaturization, enhance performance and functionali- ties such as enabling on-chip high-speed parallel AFM. During the micro-fabrication process, residual stresses develop in the different layers of the cantilever beam, causes initial deflection. The residual stress in the different layers of the cantilever beam and the application of voltage to the PZT thin-film affects their dynamics. This the- sis investigates the dynamic behaviour and develops a control technique and a novel charge readout circuit to improve the performance of a micro-fabricated multi-layer prestressed piezoelectric cantilever beam as an actuator and a deflection sensor. Firstly, the fabrication process of a unimorph PZT cantilever beam is explained. A low thermal budget Ultra-high vacuum e-beam evaporated polysilicon thin-film (UHVEEpoly) process is used for the fabrication of multi-layered PZT cantilever beam in d31 mode. The sharp peaks at resonant frequencies in the frequency response of the PZT cantilever beam show very little damping and a large settling time of the cantilever beam. Secondly, the dynamic behaviour of the prestressed PZT cantilever beam is in- vestigated subjected to change in driving voltage. Experimental investigations show a shift in resonant frequencies of a PZT cantilever beam. However, there is no reported mathematical model that predicts the shift in resonance frequencies of a multi-layered prestressed piezoelectric cantilever beam subjected to a change in driving voltage. This work developed a mathematical model with experimental val- idation to estimate the shift in resonance frequencies of such cantilever beams with the change in the driving voltage. A very good agreement between the model predic- tions and experimental measurements for the frequency response of the cantilever beam at different driving voltages has been obtained. A novel linear formulation has been developed to predict the shift in resonance frequencies of the PZT can- i tilever beam for a wide range of driving voltages. The formulation shows that the shift in resonance frequencies of a multi-layered prestressed piezoelectric cantilever beam per unit of applied voltage is dependent on geometric parameters and material properties. Thirdly, a robust resonant controller has been designed and implemented to re- duce the settling time of a highly vibrating PZT cantilever beam. The controller design is based on a mixed negative-imaginary, passivity, and a small-gain approach. The motivation to design a resonant controller using the above-mentioned analyti- cal framework is its bandpass nature and the use of velocity feedback, as the charge collected from a vibrating PZT cantilever beam gives the velocity information of the beam. The proposed controller design results in finite gain stability for a pos- itive feedback interconnection between two stable linear systems with a large gain and phase margin. Experimental results demonstrate that the designed resonant controller is able to effectively damp the first resonant mode of a cantilever, signifi- cantly reducing settling time from 528 ms to 32 ms. The robustness of the designed resonant controller is tested against changes in the cantilever beam dynamics due to residual stress variation and or stress variation due to driving voltage. Finally, to facilitate the miniaturization of on-chip sensors and parallel high- speed AFM, a single layer of a PZT thin-film in a cantilever beam is used as a deflection sensor and an actuator instead of bulky optical deflection sensors. A novel charge readout circuit is designed for deflection sensing by capturing the electrical charge generated due to the vibration of the PZT beam. The signal-to-noise ratio and sensitivity analysis of the readout circuit shows similar results compared to the commercially available optical deflection sensors. Our work highlights very important aspects in the dynamic behaviour and perfor- mance of a multi-layered prestressed piezoelectric cantilever beam. The agreement between the proposed theoretical formulation and experimental investigations in modeling, control design, and a novel readout circuit will provide the platform for further the development and miniaturization of microcantilever-based technologies, including on-chip parallel HS-AFM.
dc.identifier.uri http://hdl.handle.net/1959.4/101629
dc.publisher UNSW, Sydney
dc.rights CC BY 4.0
dc.rights.uri https://creativecommons.org/licenses/by/4.0/
dc.subject.other Mathematical model
dc.subject.other MEMS
dc.subject.other Prestressed Piezoelectric
dc.subject.other Cantilever beam
dc.subject.other Residual stress
dc.subject.other Resonance frequencies
dc.subject.other Resonant controller
dc.subject.other Vibration control
dc.subject.other Negative-Imaginary
dc.subject.other Robust
dc.subject.other Self-sensing and self-actuating
dc.subject.other Charge readout circuit
dc.title Modeling and Control of MEMS-based Multi-layered Prestressed Piezoelectric Cantilever Beam
dc.type Thesis
dcterms.accessRights open access
dcterms.rightsHolder Nawaz, Muhammad Haq
dspace.entity.type Publication
unsw.accessRights.uri https://purl.org/coar/access_right/c_abf2
unsw.date.workflow 2023-11-13
unsw.identifier.doi https://doi.org/10.26190/unsworks/25336
unsw.relation.faculty Engineering
unsw.relation.faculty UNSW Canberra
unsw.relation.school School of Electrical Engineering and Telecommunications
unsw.relation.school School of Electrical Engineering and Telecommunications
unsw.relation.school School of Engineering and Information Technology
unsw.subject.fieldofresearchcode 4007 Control engineering, mechatronics and robotics
unsw.thesis.degreetype PhD Doctorate
Files
Original bundle
Now showing 1 - 1 of 1
No Thumbnail Available
Name:
public version.pdf
Size:
15.32 MB
Format:
application/pdf
Description:
Resource type